10 NEW WAYS HOW TO LACE YOUR VANS OLD SKOOL | SHOE LACING

Hey guys! In today’s video I’m going to be showing you 10 ways how to lace Vans Old Skool. This is simple tutorial about lacing Vans Old Skool and other shoes. If you have any questions, please ask in the comments, I’ll answer you as soon as possible. If you like this video don’t forget to like, comment, and subscribe! Step-by-step instructions for lacing Converse your Vans Old Skool: 0:00 - Method 1: Loosely 1. Put your laces through the first two eyelets; 2. Then make sure both ends of the lace are even; 3. Take the string in the first eyelet on the left and put it in the second on the right; 4. Take the string in the first eyelet on the right and put it in the second on the left. ( Use your finger to limit the lace); 5. Repeat this lacing pattern for the rest of the eyelet; 6. Now instead of going through the top of the eyelet, go through the bottom, from inside to out on both sides. 3:04 - Method 2: Bar lace 1. Insert each end of the shoelace downward through one of the bottom two eyelets; 2. Feed the right lace underneath the shoe so that it pops out of the third eyelet on the right side; 3. Then feed the left lace underneath the shoe so that it pops out of the second eyelet on the left side; 4. Cross the left lace over to the right side and insert it downward through the second eyelet; 5. Then cross the right lace over to the left side and insert it downward through the third eyelet; 6. Repeat this lacing pattern for the rest of the eyelet. 5:51 - Method 3: Zig-zag 1. Put the lace through the eyelets not over the top; 2. Take the lace from the inside of the sneaker and go through the next eyelet up and across; 3. Then do the same with this lace but on the other side; 4. Repeat these steps until you reach the final eyelets; 5. Insert the right lace through the loop you have now created on the right; 6. Repeat this lacing pattern for the rest of the eyelet; 8:35 - Method 4: X & Bar lace 1. Place one end of the shoelace through the second top left hole; 2. Then thread the right end of the shoelace into the first left hole from the top; 3. Put that same string to the first right eyelet from the bottom; 4. Then put that same string to the second right eyelet from the bottom; 5. Now put that same string to the first left eyelet from the bottom; 6. Put that same string to the second left eyelet from the bottom; 7. Using the left end, thread it in the opposite hole in a straight line. 8. Then insert the end of the shoelace into the next right eyelet; 9. Keep going until you reach the final eyelets; 10. Pass the same rope again through the second right eyelet from the top. 12:30 - Method 5: Section 1. First of all put your laces through the first two eyelets; 2. Then, make sure both ends of the lace are even; 3. Take the string in the last eyelet on the left and put it in the fifth on the right; 4. Then put it in the second on the left; 5. Now put it in the sixth on the right; 6. Repeat this for the rest of the loops; 7. Take the string in the last eyelet on the right and put it in the fifth on the left; 8. Then put it in the second on the right; 9. Now put it in the sixth on the left; 10. Repeat this for the rest of the eyelet. 12:30 - Method 6: Diamond 1. Starting from the two bottom opposite facing holes, insert each end of the shoelace from the inside. Make sure both sides of the remaining laces are equal; 2. Take the lace in the last eyelet on the right and put it in the third on the left; 3. Then put that same lace under to the previous eyelet; 4. Then take the lace in the last eyelet on the left and put it in the third on the right; 5. Then put that same lace under to the previous eyelet; 6. Repeat this lacing pattern for the rest of the eyelet. 18:43 - Method 7: Big diamond 1. First of all put your laces through the second bottom eyelets; 2. Then make sure both ends of the lace are even; 3. Hide the lace under the tongue of the sneakers; 4. Take the right lace and thread it from the bottom into the first eyelet; 5. Then thread the same lace into the eyelet; 6. Take the left lace and thread it from the bottom into the first eyelet; 7. Then thread the same lace into the eyelet; 8. Insert the first left end of the shoelace into the fourth right hole from the bottom; 9. Then thread it from the bottom into the third eyelet; 10. Now thread the same lace into the eyelet; 11. Insert the first right end of the shoelace into the fourth left hole from the bottom; 12. Then thread it from the bottom into the third eyelet; 13. Now thread the same lace into the eyelet; 14. Repeat this for the rest of the eyelets. Unfortunately, due to the limitation of the number of characters in the description under the video, I cannot insert a lot of step-by-step instructions:( 0:00 Loosely 3:04 Bar lace 5:51 Zig-zag 8:35 X & Bar lace 12:30 Section 15:01 Diamond 18:43 Big diamond 21:57 Slash lines 24:45 Star 27:30 Spiral